o ring

Study on Structure of O Ring Seal

O形橡胶密封圈封油结构研究

The application of rubber O ring static seal at cryogenic temperature

橡胶O形环在低温静密封中的应用

Hermeticity analysis on the bounce - back process of O ring

橡胶密封圈在回弹过程中的密封性能分析

Effect of flange deformation on seal of O ring

凸缘边变形对O形圈密封的影响

An Analysis for Finite Elastoplastic Deformation and Cyclic Relaxation of Confined O Ring for Pressure Vessel

O形密封环的弹塑性大变形和循环松弛分析

The work design and structure of o ring conveying rubber belts for special continuity were studied in this paper .

研究了有特殊连续性要求的环形输送带带芯的结构设计及施工设计。

The analysis method in this paper is conducive to the correct selection of O ring seals especially in case of important applications .

为重要场合下O形密封圈的正确选用提供了一种方法。

Experimental research on load decay of two kinds of O ring made of different silicone rubber under different temperature has been conducted .

对两种硅橡胶材料O形圈的载荷衰减规律进行了试验研究，结果发现，O形圈的载荷衰减规律与O形圈材料的性能有关；

Processing of multichamber mould for rubber sealing O ring

O形橡胶密封圈多腔模具的加工工艺

It was mainly used in the oil seal , O ring and gasket etc. of automobile engine , transimission system and wheel axle .

它主要用于汽车发动机、传动系统及轮轴上的油封、O形圈、垫片等密封产品。

The bushes and bearing pins of the rubber O ring roller chains were characterized by stress fatigue wear and adhesion wear ;

O形圈链条中销轴和套筒的磨损主要以疲劳磨损为主，并伴随着粘着磨损；

The design calculation of the large O ring rubber self energized seal ( without bolt and nut ) used for the vacuum equipment and its application results are introduced .

介绍真空设备法兰采用大直径O形环橡胶自紧式密封（不用螺栓和螺母）的设计计算及其应用效果。

Are products are : water polo foot O ring gasket seals sucker Washers silicone chip nail head gasket sets of plastic earplugs dust jacket sets of rings , such as sealing ring .

现生产的产品有：脚垫O环水球密封圈吸盘华司垫圈矽胶片灯头套胶钉垫片耳塞防尘套护套套环止水环等。

Experimental leakage simulation of the 2-level large-scale hollow metallic ring seal and 3-level rubber O ring seal was performed with several high precision leak detectors , based on helium mass spectroscopy , to verify leakage theory of multi-level series seal .

为进一步验证多级串联密封系统的泄漏理论和规律，分别进行了双道大型空心金属圈模拟试验和三道橡胶圈泄漏模拟实验，试验中综合采用了灵敏度很高的各种氮质谱检漏方法。

There was a new ringed structure on the driven pan to push back the oil and we also used single framework with one O ring instead of double framework to seal the oil . Both of the structure can improve the sealability of the timing advancer .

在提前器从动盘上设计了一个挡油环形结构，并将原来的双骨架密封结构改为单骨架结构加O型圈密封结构。

An Optimization Design of the Expansion Joint with O - Ring

O形膨胀节的优化设计

How to fully use the o sealing ring function effect

O形密封圈功能的充分发挥

Sealing structure design of hollow metal O - ring

金属空心O形圈密封结构设计

The sealing structure and principle of hollow metal O - ring was introduced .

介绍了金属空心O形圈的密封结构和密封机理。

Determination of Minimum Compression of O - ring for Rotating Sealing

旋转密封○形圈最小过盈量的确定

Measures of Decreasing Compression Deformation of O - Ring

降低O形圈压缩变形的措施

The Applications and Advances of O - ring Seal

O圈密封的应用及进展

Frictional drag produced by piston o & ring

O型活塞密封圈所产生的摩擦阻力

Analysed the principle of O sealing ring , based on the principle , put forward some fully using suggestions on sealing ring .

分析了O型密封圈的密封机理，在此基础上提出了充分发挥密封圈功能的几条切实可行的措施。

The sealing property of rubber sealing X - ring is superior to that of O - ring as applying , but the process of sealing X - ring is difficult .

在应用橡胶圈的密封技术中，X形橡胶密封圈比O形橡胶密封圈具有更优越的密封特性。但由于模具加工难，限制了应用的普遍性。

Focuses on the double " O " ring connection , the scene ends meet connections , flanged connections , such as connections and their respective conditions of application and quality control points .

重点论述了双“○”圈连接、现场糊口连接、法兰连接等连接方式及其各自的适用条件与质量控制要点。

In the aspect of interface place design between the plug and the receptacle , we have adopted " O " ring block structure to stop the contracts node discharge way from the ground in the interface place .

在插座和插头的配合界面的设计上，应用了O形环阻断结构隔绝内电极对地的通路；

By experiments and scientific data , it expound and prove that the service life and sealing function of O sealing ring relate directly to service conditions , assembly quality , processing precision , lubricating conditions and dustproof measure etc.

并通过试验结果及科学数据论证了O形圈使用寿命和密封性与使用条件、装配质量、加工精度、润滑情况、防尘措施等有着直接关系。

Describes the leaking of the " O " ring between inner and outer cylinders of syngas compressor in methanol plant , analyzed the reasons for the leaking , and proposes measures against the leaking .

阐述了甲醇装置合成气压缩机内外缸体间“O”型环的泄漏情况，对泄漏原因进行分析，提出解决措施。

This paper introduces the cause of the seepage in valve box of oil isolation pump , and solves the problem of the valve box seepage by way of the improvement of die slot in O - ring and seal material .

本文介绍油隔离泵阀箱渗漏的原因，能过对阀盖O型圈沟槽的改进及采取乐泰密封胶替代牛油盘根进行密封，解决了阀箱渗漏的问题。